How to Fix Common Vape Issues: Troubleshooting guide

While vaping can be an enjoyable and satisfying experience, occasional issues may arise that disrupt your vaping session. From leaky tanks to burnt coils, understanding how to troubleshoot common vape problems can help you quickly resolve issues and get back to enjoying your vape turn carts. In this guide, we’ll cover some of the most common vape issues and provide practical solutions to fix them.

1. Leaking Tank:

  1. Check Seals and O-Rings: Inspect the seals and O-rings on your tank for any signs of damage or wear. Replace any damaged seals to ensure a tight seal and prevent leaks.
  2. Proper Assembly: Ensure all components of your tank are properly assembled and tightened. Over-tightening can cause leaks, so tighten the tank just enough to create a seal without stripping threads.
  3. Adjust Coil and Wick: Improperly installed or flooded coils can lead to leaking. Make sure the coil is securely screwed into place and the wicking material is properly saturated but not overfilled.
  4. Avoid Overfilling: Do not overfill your tank, as excess e-liquid can leak through airflow vents. Leave some space at the top of the tank to accommodate expansion and prevent leaks.

2. Burnt or Dry Hits:

  1. Prime New Coils: Before using a new coil, prime it by saturating the wicking material with e-liquid. Allow the coil to soak for a few minutes to ensure proper saturation and prevent dry hits.
  2. Lower Wattage: If you’re experiencing burnt or dry hits, try lowering the wattage on your device. High wattages can cause coils to overheat and burn the wicking material, resulting in a harsh and unpleasant taste.
  3. Proper Wicking: Ensure the wicking material is properly trimmed and positioned within the coil. Avoid packing too much cotton, as this can restrict e-liquid flow and lead to dry hits.
  4. Avoid Chain Vaping: Give your coil time to re-saturate between puffs to prevent dry hits. Chain vaping (taking consecutive puffs without allowing the coil to re-wick) can cause the wicking material to dry out and burn.

3. No Vapor Production:

  1. Check Battery Connection: Ensure the battery or device is turned on and securely connected to the atomizer. Clean the battery contacts and atomizer connection to remove any dirt or debris that may be interfering with the connection.
  2. Inspect Coils: Check the coils for signs of damage or wear. Replace worn-out coils or coils with burnt wicking material to restore vapor production.
  3. Adjust Airflow: Experiment with airflow settings on your atomizer to find the optimal airflow for vapor production. Closing off airflow too much can restrict vapor production, while too much airflow can dilute vapor density.

4. Gurgling or Flooding:

  1. Clear Airflow: Remove the tank from the device and blow through the airflow holes to clear any excess e-liquid or condensation.
  2. Adjust Wick Density: If using a rebuildable atomizer, adjust the density of the wicking material to prevent flooding. Too much wicking material can trap excess e-liquid and cause flooding, while too little wicking material can lead to dry hits.
  3. Avoid Over-Priming: When priming coils, be careful not to over-prime or flood the coil with e-liquid. A few drops of e-liquid directly onto the coil should be sufficient to saturate the wicking material without flooding the coil.

5. Battery Issues:

  1. Check Battery Level: Ensure your battery is adequately charged. If using a removable battery, try swapping it out for a fully charged battery.
  2. Clean Battery Contacts: Clean the battery contacts with a cotton swab dipped in isopropyl alcohol to remove any dirt or residue that may be interfering with the connection.
  3. Check for Damage: Inspect the battery for any signs of damage or wear, such as dents, leaks, or corrosion. Replace damaged batteries immediately to prevent safety hazards.


By following these troubleshooting tips, you can quickly identify and resolve common vape issues, ensuring a smooth and enjoyable vaping experience. Remember to practice proper maintenance, priming, and usage techniques to prevent issues from occurring in the first place. If problems persist despite troubleshooting efforts, consider seeking assistance from a knowledgeable vape retailer or technician. Happy vaping!

Leave a Reply

Your email address will not be published. Required fields are marked *